RenergyWare NEMA 4 SCADA Enclosure

RenergyWare Hardware Packages

Field-proven NEMA 4 enclosures built for the dirt. Fabricated in-house, UL listed, and bench-tested before they ever reach your site.

Request Integration Quote
What ships from Charlotte

Industrial hardware, factory accepted before it leaves the bench.

Consumer-grade IT hardware does not survive a solar field. Temperatures swing 100°F, dust coats every surface, grid transients fry cheap PSUs. Every RenergyWare panel is built around a fixed bill of materials we have run for thousands of hours — and we power-up, simulate, and stress-test each one before it ships.

RenergyWare · Type P3

  1. Moxa EDS-528E

    Industrial Ethernet Switch

    24× FE + 4× GbE · Layer 2/3 · turbo-ring < 20 ms

    LINK

  2. SEL RTAC-3530

    Logic Engine + Protocol Gateway

    IEC 61131-3 · DNP3 · Modbus TCP · IEC 61850

    RUN

  3. IPC-DAS WP-9000

    Data Concentrator

    128 Modbus tags · historian buffer · MQTT egress

    OK

  4. Sierra RV50X

    Cellular Backhaul

    LTE Cat-4 · failover to satellite · IPSec VPN

    −67 dBm

  5. Phoenix Contact QUINT

    24 VDC PSU + Breakers

    120 W · UL 508A breakers · surge protection

    PWR

Enclosure

NEMA 4 · IP66 eq.

Listing

UL 508A

Op temp

−40 / +60°C

Built in

Charlotte NC

Industrial-grade BOM

Components we trust on Sunday at 3am

Moxa for the network, SEL for the logic, IPC-DAS for the data, Sierra for the backhaul, Phoenix Contact for power. We do not substitute. We carry critical spares.

Pre-programmed delivery

IP schema and tag map locked

Field commissioning becomes "plug, label, verify" — not "debug from scratch." The panel arrives knowing your VLAN, your tag list, and your time source.

Bench-test certificate

Every panel has a serial & a signature

FAT report ships with the unit: power-up sequence, comm link verification, alarm exercise, time-sync drift < 50 ms over 24 h. Signed, dated, archived.

UL 508A · NEMA 4

Built to the listing, not around it

UL 508A panel listing held in-house. NEMA 4 enclosure rated for hose-down, dust ingress, and wind-driven rain. No corner-cutting on the outer shell.

  • Drop-in replacement units stocked
  • Identical fleet across portfolios
  • Cellular + satellite failover
  • Surge protection on every line
Why we build them ourselves

A fleet you can actually maintain.

Every site identical. Every spare interchangeable. Every alarm class shared.

In-house UL 508A fabrication

Every panel built in our Charlotte, NC facility under a held UL 508A listing. Wiring runs photographed, components labelled, BOM frozen against your project drawing.

Bench-tested before delivery

Power-up, comm-link exercise, alarm walk-through, and 24-hour soak before the panel leaves the shop. DOA components caught here, not on a Sunday call-out from site.

Spares + lifecycle support

Critical components stocked for same-week swap-out. EOL roadmaps tracked per OEM so your fleet stays serviceable for the full 25-year asset life.

Frequently Asked Questions

Both. Most projects bundle the panels with a full REIG SCADA / DAS / commissioning scope, but we also sell stand-alone units to EPCs and asset owners running their own integration crews. Either way the FAT report and as-built drawing ship in the box.
The base configuration is fixed — that's the point of a fleet hardware product. We do customise the I/O density, the cellular carrier, and the IP schema per site. We won't substitute the core components: we've seen what fails on a hot day in year three.
Six to ten weeks for a full Type P3 build, depending on chip-supply at the time of order. We carry stock of the most common configurations for emergency replacements.

Standardise your SCADA fleet.

Deploy consistent, rugged hardware across your entire portfolio.

Request Project Consult
Call UsConsultSubmit RFP