Why Solar PV Systems Need Monitoring

Solar PV monitoring went from an optional add-on to required infrastructure in less than a decade, and the shift was not driven by efficiency reports. It was driven by two rooftop fires, in Bakersfield, California and Mount Holly, North Carolina, that happened within a short window of each other and forced the industry to rethink what "set it and forget it" solar actually meant. This piece traces that history, from the first Data Acquisition Systems through today's SCADA platforms, Power Plant Controllers, and microgrid control systems, and makes the case for why solar PV monitoring now belongs on every project, not just the 100 MW plants that make headlines.
Why Solar PV Monitoring Became Mandatory After the Bakersfield and Mount Holly Fires
Solar PV monitoring became a requirement, not a preference, after two commercial rooftop fires in Bakersfield, California and Mount Holly, North Carolina struck within a short span of each other in the plants' early years of operation, triggering formal investigations that traced the failures to undetected ground faults and prompted new monitoring and shutdown requirements across the industry.
In the early days of the solar PV industry, the prevailing wisdom held that a solar PV power plant could be built and then left alone for 25 years. Most of these early systems went up on commercial rooftops: the panels had no moving parts, the electrical system was time-tested and met requirements under the National Electrical Code (NFPA 70), and the inverters needed little more than the occasional filter change. Once the system was paid off, it did nothing but produce money for its owner. That assumption did not survive contact with reality.
Within a short period after two large rooftop systems, large for their era, were built and producing power, fires broke out on two separate rooftops a country apart. The Bakersfield, CA and Mount Holly, NC fires became the catalyst not just for determining root cause, but for building solutions that would keep it from happening again. One outcome was the addition of a monitoring system that let a remote operator track plant performance and watch the Bender ground fault detection devices for faults or shutdowns. Solar PV monitoring stopped being a luxury line item and became a necessity. Equipment-level safety standards such as UL 3741 for PV hazard control (UL) grew out of the same post-fire scrutiny that pushed monitoring requirements forward.
From Data Loggers to SCADA: 12 Years of Monitoring Evolution
Solar monitoring shifted from simple data logging to full SCADA control within about twelve years, as utilities began requiring that PV plants operate like any other generation asset on the grid, a jump that added Real Time Automation Controllers, protective relays, utility-grade metering, and control servers to what used to be a web-connected data logger.
Fast-forward twelve years or so and look at where solar monitoring stands today. The earliest tools were Data Acquisition Systems (DAS): they collected data and displayed it on a web portal for an operator to check and download. But as plants grew larger and more complex, the utilities on the other end of the interconnection agreement expected the PV plant to behave like any other generation asset on their grid. That meant Supervisory Control and Data Acquisition (SCADA systems), which brought far more depth of information and, for the first time, the ability to control the plant directly. IEEE's standards work on grid-interactive inverters and SCADA integration (IEEE) reflects how far that bar has moved. Where a data logger and a web connection used to be enough, SCADA now runs on Real Time Automation Controllers, protective relays, utility-grade metering, servers running control algorithms, and historians that keep years of performance data on hand. It has been a leap forward in the industry, matching the overall growth of the PV market.
Why SCADA Replaced Simple Data Acquisition Systems
SCADA replaced simple DAS because utilities needed two-way control, not just visibility: a data logger can tell an operator a plant is online, but it cannot curtail output, respond to a ride-through event, or coordinate with a utility's own grid management system in real time.
DAS vs. SCADA vs. PPC vs. Microgrid: Comparing Solar PV Monitoring Architectures
Choosing the right monitoring architecture comes down to plant scale and utility requirements: a small rooftop array can run on DAS alone, while a utility-scale plant with curtailment obligations or islanding capability needs SCADA, a PPC, or a microgrid controller layered on top of it.
| System Type | Primary Function | Typical Scale | Core Components | Utility Interaction |
|---|---|---|---|---|
| DAS (Data Acquisition System) | Collects and displays production data | Rooftop to mid-size ground mount | Data logger, web portal, basic sensors | Reporting only, no direct control |
| SCADA | Monitors and controls plant operation in real time | Utility-scale plants (10 MW+) | Real Time Automation Controllers, protective relays, utility-grade metering, historians | Two-way: reporting plus remote control |
| PPC (Power Plant Controller) | Regulates plant output against interconnection limits | Utility-scale plants with PPAs or curtailment requirements | Control algorithms, inverter setpoint management, SCADA integration | Active compliance with utility production limits |
| Microgrid Controller | Manages grid-tied and islanded operation modes | Campus, military, community, and commercial microgrids | Mode-transfer logic, protective relays, DER coordination | Switches safely between grid-tied and islanded states |
Does Every Solar Project Need Monitoring, Not Just Utility-Scale Plants?
Yes: every solar PV system above residential scale benefits from some form of solar PV monitoring, because even a 250 kW rooftop array carries the same ground-fault and arc-fault risks as a 100 MW plant, just packaged into a simpler Data Acquisition System instead of a full SCADA platform.
Of course, the solar PV industry is not made up entirely of 100 MW-plus systems, even though those projects pull most of the press coverage. There are hundreds of thousands of smaller, far-flung solar PV systems built across all 50 states. Setting aside single-family residential, every PV system of any real capacity benefits from some kind of monitoring. Generally, the smaller the system, the simpler the DAS can be, though site factors and local utility interconnection requirements create exceptions to that rule. The U.S. Department of Energy's distributed solar research (DOE) and NREL's grid integration studies (NREL) both document how quickly those interconnection requirements are tightening as distributed solar grows.
Rooftop Solar and BESS Are Reviving Distributed Monitoring Demand
Rooftop solar is making a comeback paired with battery energy storage systems (BESS), and that pairing is pushing solar PV monitoring back into distributed, smaller-footprint projects that a decade ago might have gotten by with a basic data logger and nothing else.
Facilities are looking for relief from demand charges and rising energy costs, and a BESS only delivers that relief if its monitoring system can see both the PV production data and the battery's state of charge at the same time. Smaller ground-mount systems are appearing in large numbers and getting assembled into larger portfolios of energy assets, which need monitoring and, in some cases, a layer of control. Battery energy storage systems (BESS) add a second set of telemetry (state of charge, cycle count, and thermal data) that has to be visible alongside the PV data, or the economics of the project do not work.
Power Plant Controllers and Utility Compliance
Power Plant Controllers (PPC) let a plant produce at its maximum in the early morning and late afternoon, when irradiance is lower, while holding output below the cap set in the plant's power purchase agreement during the highest-irradiance hours of midday.
Power Plant Controllers are evolving to do both jobs well: push output up when the sun allows it and pull output back down during peak irradiance so the plant does not exceed the energy production limits agreed to with the connected utility. Getting that balance right is itself a form of solar PV monitoring, just one with an active control loop attached to it.
Microgrids Require Monitoring and Control to Operate Safely
Microgrids need monitoring and control because they can operate two different ways, tied to the grid or fully islanded, and switching between those two states without a monitoring and control layer risks the kind of undetected fault that caused the Bakersfield and Mount Holly fires in the first place.
Microgrids are becoming more mainstream, and given their role both on and off the grid, a monitoring and control system is required to keep performance safe and reliable. The Department of Energy's microgrid research (DOE) points to the same conclusion as the earlier fire investigations: a microgrid without real-time visibility into its own state carries meaningfully more risk than one that has it.
All of these plant types (utility-scale, distributed rooftop, ground-mount portfolios, and microgrids) now require monitoring and, in a growing number of cases, an added layer of control. With little standardization across the PV industry, no two monitoring or PPC platforms look exactly alike. Meeting that variability takes well-built hardware and software, designed, installed, and commissioned by engineers, designers, installers, and communications specialists who have done it before. The industry needs more of these systems, not fewer, and needs them to run reliably, day after day.
Frequently Asked Questions About Solar PV Monitoring
What is the difference between solar PV monitoring and SCADA?
Solar PV monitoring is the broader category: any system that collects performance data, from a basic Data Acquisition System (DAS) reporting production totals to a full Supervisory Control and Data Acquisition (SCADA) platform. SCADA is the more capable end of that category. It adds two-way control, Real Time Automation Controllers, protective relays, utility-grade metering, and historians on top of the same data collection a DAS performs, so an operator can not only see a ground fault or curtailment event but also act on it remotely. Smaller plants often run on DAS alone; utility-scale plants interconnecting under utility SCADA mandates generally need the full platform.
Do small or rooftop solar systems need monitoring, or is that only for utility-scale plants?
Small and rooftop systems need monitoring too, just a simpler version of it. Excluding single-family residential, nearly every PV system benefits from some Data Acquisition System, because the same ground-fault and arc-fault risks that affected the Bakersfield and Mount Holly commercial rooftop plants exist at smaller scales. The complexity of the monitoring system can scale down with the plant: a 250 kW commercial rooftop array does not need a full SCADA platform, but site-specific factors like utility interconnection requirements, demand-charge management, or a paired battery energy storage system can push even a small project toward a more capable monitoring setup.
What caused the Bakersfield and Mount Holly solar fires?
Both fires followed undetected ground faults in large, for their time, commercial rooftop solar PV systems, at a point when the industry still treated monitoring as optional. Investigations into the incidents pushed the industry toward pairing monitoring systems with Bender ground fault detection devices, so a remote operator could see a ground fault or an automatic shutdown as it happened instead of learning about it from a damaged roof. The two fires, roughly a country apart from each other, are generally credited as the turning point that moved solar PV monitoring from a nice-to-have feature to a baseline requirement on commercial systems.
What does a Power Plant Controller (PPC) do?
A Power Plant Controller manages how much a solar plant is allowed to produce at any given moment, based on the limits set in its interconnection or power purchase agreement with the utility. It lets the plant run at full output during lower-irradiance hours, early morning and late afternoon, and holds output below a cap during peak midday irradiance so the plant does not exceed its agreed production level. A PPC works alongside the plant's broader monitoring system, reading real-time production data and adjusting inverter setpoints, so it functions as an active control layer on top of standard solar PV monitoring.
Why do microgrids need their own monitoring and control system?
Microgrids need monitoring and control because they can switch between two different operating states: connected to the main grid, and islanded, running independently off it. That transition has to happen without creating the kind of undetected fault condition that caused early rooftop solar fires. A monitoring and control system gives an operator real-time visibility into which state the microgrid is in, whether a fault condition exists, and whether a transition between grid-tied and islanded operation is happening safely. Without that visibility, a microgrid carries meaningfully more risk than a conventional, always grid-tied solar PV system.
